> For the complete documentation index, see [llms.txt](https://ignitedigi.gitbook.io/ignite-digi-wiki/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://ignitedigi.gitbook.io/ignite-digi-wiki/home/control-ecosystem-manual/product-manuals/control_deck_manual/menu-when-controlling-ronin-2-rs4-pro.md). # Menu when controlling: Ronin 2 / RS4 Pro Control Deck remembers it's previous settings when power cycling, or you reconnect to a device type.\ **Example:** Going between 4D and Ronin 2, any 4D specific settings will be remembered for when you connect back to it.

MENU ITEM	OPTIONS	DESCRIPTION
Exit Menu	-	You can quickly exit the menu at anytime, by holding MENU/SETUP button (second from right)
Joystick Expo	L / 2 / 3
Joystick Fn	Twist: On/Off Button: On/Off	Enable or Disable the Twist Axis or Button on the Joystick. Twist setting ON is not overridden by Roll Speed OFF
PTR Direction	Axis: P/T/R Invert: Off/On	Toggle the control direction for Pan, Tilt and Roll axis. Shortcut for toggling Tilt Axis direction is still long hold on Joystick Button (in most modes), unless button is turned off in Joystick Fn (above)
Roll Speed	Off / L / M / H	Off : Disable roll input on Joystick or Rocker. Roll Trim will ALWAYS remain available! L: Low M: Medium H: High
Zoom/Roll Swap	Normal / Swapped	Normal is Zoom on Rocker, Roll on Twist. Swapped is Roll on Rocker, Zoom on Twist
FIZ Control *this setting will disappear when Fusion Hub setting is On.	FIZ / Zoom / Off	FIZ: Control 1 x DJI RS or Focus Pro Motor that's on RS4 Pro, or on LiDAR Hub. Zoom: Not applicable to this use case Off: No FIZ motor control
Focus Knob Cal.	Calibrate	This calibrates the focus knob on the Control Deck, not the FIZ motors! Turn the Focus Knob to each end gently until it says Complete. You may find it says Complete after just a partial movement, this is because it's tracking the endpoints in the background even when you're not in the menu. It will only calibrate for the full range of the knob.
Shake Mode	1 / 2 / 3	Change the shake algorithm
Shake On Move	On / Off	On: Shake will continue on all axes, regardless of joystick input. Off: Shake will only be on axis that are not getting input from joystick, once input from joystick stops that axis will ease into shake again.
Shake Axis	Axis: P / T / R Shake: On / Off	Enable or disable shake on each axis: Pan / Tilt / Roll
RS Motor *this setting will disappear when Fusion Hub setting is On.	Knob / Rocker	Knob: Control the RS/Focus Pro motor via the focus knob on Control Deck. Rocker: Control the RS/Focus Pro motor via the rocker on Control Deck.
R2 User Profile	1 / 2 / 3 / 4 / 5	When using RS4 Pro: 1: PTF 2: FPV / 3D Roll 360 / Custom We recommend setting to Custom and then turning off each axis follow via the pencil symbol top right of the gimbal screen. 3/4/5: N/A When using Ronin 2: 1: User Profile 1 2: User Profile 2 3: User Profile 3 4: User Profile 4 5: User Profile 5 A long press of MODE button on Control Deck will cycle between User 1 and 2 on RS4 Pro and Ronin 2
Fusion Hub	Off / On	Off: If no Fusion Hub is in line, ensure you have this setting to Off. If you have it set to On but have no Fusion Hub in line, you will get erratic gimbal movements. On: For use when you have Fusion Hub on the DJI TX. See below for the new menu items that appear when this setting is On.

#### Fusion Hub ON adds the following menu items

MENU ITEM	OPTIONS	DESCRIPTION
Focus Curve	25% / 50% / 75%	Gives you the ability to offset the focus mapping for more precision at one end of the lens' focus range. Similar to Near/Far setting on your Canon/Fujinon focus demand. Works with Nucleus-M, M2, Nano II, MōVI motors and Servo lenses.
Fusion Focus	Dir. : CW / CCW Torque : L / M / H	Dir. CW / CWW: Change the direction of the motor relative to the focus knob Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Iris	Dir. : CW / CCW Torque : L / M / H	Dir. CW / CWW: Change the direction of the motor relative to the iris knob Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom A	Dir. : CW / CCW Torque : L / M / H	Dir. CW / CWW: Change the direction of the motor relative to the zoom rocker not applicable when using Servo lens Torque* L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom B	Speed : L / M / H Damping : L / M / H	Speed L / M / H: Set the maximum speed of the zoom. Damping L / M / H: Set the amount of damping, to help ease in and out of zooms
MōVI Motor Type	0 - 7 (in 1 step increments)	This setting is not applicable for Ronin 2 / RS4 Pro use case
Iris Control	Iris / ND	Change the mapping of iris knob between iris and VND when using Tilta Nucleus M, M2 or Nano II motors. Iris (motor 2) VND (motor 4)
FIZ Handoff	FIZ / FI / F / I	Use this setting to hand off FIZ axis to the Tilta Hand Unit connected to FIZBUSTER (standalone or rear port of Control Deck) FIZ: Focus, Iris and Zoom FI: Focus and Iris (Control Deck still has Zoom) F: Focus (Control Deck still has Iris and Zoom) I: Iris (Control Deck still has Focus and Zoom)
Servo Link	FIZ / FZ	Only applicable when using Servo Link Allows you to control iris on Servo lenses, or to relinquish iris control to the camera, for auto iris or CCU control. FIZ: You will have Focus, Iris and Zoom on Control Deck FZ: You will have Focus and Zoom on Control Deck
PTR/Zoom Ratio	1:1 - 1:25 (in 1 step increments)	Also known as Zoom scaling, it allows you to set a ratio of how much the pan/tilt/roll axis speeds will lower relative to the zoom position of the lens. Example: Canon 17-120mm, try 7:1 setting. As you zoom in, Control Deck will adjust the axis speeds for a consistent feel and look.
FIZ Calibrate	Calibrate	Remotely trigger calibrate on Nucleus-M, M2, Nano II or MōVI FIZ motors. If the motors have recently completed a calibration, then this may not work. Not applicable when using Servo Link