Menu when controlling: MōVI Pro / XL
This is in order as you will see it on the Control Deck when connected to a MōVI Pro / XL
Control Deck remembers it's previous settings when power cycling, or you reconnect to a device type. Example: Going between 4D and Ronin 2, any 4D specific settings will be remembered for when you connect back to it.
Exit Menu
-
You can quickly exit the menu at anytime, by holding MENU/SETUP button (second from right)
Joystick Expo
L / 2 / 3
Twist Axis
On / Off
Enable or Disable the Twist Axis on the Joystick. This is not overridden by Roll Speed OFF
Zoom/Roll Swap
Normal / Swapped
Normal is Zoom on Rocker, Roll on Twist. Swapped is Roll on Rocker, Zoom on Twist
Focus Knob Cal.
Calibrate
This calibrates the focus knob on the Control Deck, not the FIZ motors! Turn the Focus Knob to each end gently until it says Complete. You may find it says Complete after just a partial movement, this is because it's tracking the endpoints in the background even when you're not in the menu. It will only calibrate for the full range of the knob.
Roll Speed
Off / L / M / H
Off : Disable roll input on Joystick or Rocker. Roll Trim will ALWAYS remain available! L: Low M: Medium H: High
Shake Mode
1 / 2 / 3
Change the shake algorithm
Shake On Move
On / Off
On: Shake will continue on all axes, regardless of joystick input. Off: Shake will only be on axis that are not getting input from joystick, once input from joystick stops that axis will ease into shake again.
Shake Axis
Axis: P / T / R Shake: On / Off
Enable or disable shake on each axis: Pan / Tilt / Roll
R2 User Profile
1 / 2 / 3 / 4 / 5
1: Majestic Mode 2: Dual Op Mode 3: Kill gimbal motors 4: N/A 5: N/A A long press of MODE button on Control Deck will cycle between Majestic and Dual Op Modes on MōVI Pro / XL A long press of CLEAR MARK button on Control Deck will cycle between Kill gimbal motors and Dual Op Modes on MōVI Pro / XL
Fusion Hub
Off / On
Off: If no Fusion Hub is in line, ensure you have this setting to off. If you have it set to On but have no Fusion Hub in line, you will get erratic gimbal movements. On: For use when you have Fusion Hub on the DJI TX. See below for the new menu items that appear when this setting is On.
Fusion Hub ON adds the following menu items
Focus Curve
25% / 50% / 75%
Gives you the ability to offset the focus mapping for more precision at one end of the lens' focus range.
Similar to Near/Far setting on your Canon/Fujinon focus demand.
Works with Nucleus-M, M2, Nano II, MōVI motors and Servo lenses.
Fusion Focus
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the focus knob
Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Iris
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the iris knob
Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom A
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the zoom rocker *not applicable when using Servo lens Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom B
Speed : L / M / H Damping : L / M / H
Speed L / M / H: Set the maximum speed of the zoom. Damping L / M / H: Set the amount of damping, to help ease in and out of zooms
MōVI Motor Type
0 - 7 (in 1 step increments)
Allows you to change the motor type setting on MōVI Pro/XL to match the motors you are using.
0: Redrock Torque/SLS motor 1: Heden M26 2: Heden M21 3: Hocus Axis1 4: Hocus Reflex 5: Chrosziel100 6: Custom1 7: Custom2
Iris Control
Iris / ND
Change the mapping of iris knob between iris and VND when using Tilta Nucleus M, M2 or Nano II motors. Iris (motor 2) ND (motor 4)
FIZ Handoff
FIZ / FI / F / I
Use this setting to hand off FIZ axis to the Tilta Hand Unit connected to FIZBUSTER (standalone or rear port of Control Deck) FIZ: Focus, Iris and Zoom FI: Focus and Iris (Control Deck still has Zoom) F: Focus (Control Deck still has Iris and Zoom) I: Iris (Control Deck still has Focus and Zoom)
Servo Link
FIZ / FZ
Allows you to control iris on Servo lenses, or to relinquish iris control to the camera, for auto iris or CCU control. FIZ: You will have Focus, Iris and Zoom on Control Deck FZ: You will have Focus and Zoom on Control Deck
PTR/Zoom Ratio
1:1 - 1:25 (in 1 step increments)
Also known as Zoom scaling, it allows you to set a ratio of how much the pan/tilt/roll axis speeds will lower relative to the zoom position of the lens. Example: Canon 17-120mm, try 7:1 setting. As you zoom in, Control Deck will adjust the axis speeds for a consistent feel and look.
FIZ Calibrate
Calibrate
Remotely trigger calibrate on Nucleus-M, M2, Nano II or MōVI FIZ motors. If the motors have recently completed a calibration, then this may not work.
Last updated