V2.2 Notes
13th October 2025
The zip file above contains V2.2 firmware for Control Deck, Fusion Hub, FIZBUSTER and CANBUSTER
Servo Link shipped with V2.2 preloaded, so isn't included in this update.
General
TORQ Head API control, via 5-pin Lemo "MōVI Pro/XL" port on Fusion Hub. Currently in BETA on a separate firmware, get in touch if you'd like to try it out!
BaseCam Electronics API control, via 5-pin Lemo "MōVI Pro/XL" port on Fusion Hub. Currently in BETA on a separate firmware, get in touch if you'd like to try it out!
Expanded the PTR/Zoom Ratio for Fusion Hub users with Tilta or MōVI FIZ motors, or Servo zooms when using Servo Link. You can set the zoom ratio and as you zoom in, Control Deck will slow down Pan/Tilt/Roll speeds relative to the focal length, so you get consistent joystick feel as the focal length changes. We have 1:1 through to 25:1, in 1 step increments. Example: Try 7:1 for the Canon 17-120mm lens
Added Crash Zoom for Fusion Hub users with Tilta or MōVI FIZ motors, or Servo zooms with Servo Link. Press MARK button (far left on Control Deck) to crash zoom in to the end of the lens, either for an effect or to check sharps. Then when you press MARK button again, it will zoom back out to the previous focal length. When CRASH ZOOM is zoomed in, you won't be able to change focal length until you crash back out.
Added Focus Curve for Fusion Hub users with Tilta or MōVI FIZ motors, or Servo zooms with Servo Link. Allows you to offset more of the focus knob range on Control Deck to the near or far ends of lens' focus range. 50% is default, linear, no curve. 25% shifts it curve to one end (depending on motor direction) 75% shifts it to the opposite end. Particularly helpful for those shoots where you are working 10' - ∞.
Added Off to the Roll Speed menu options. Meaning you can disable roll input on Joystick or Rocker. Roll Trim will ALWAYS remain available! Known Bugs or limitations
Nucleus-M II Hand unit EXT port -> FIZBUSTER (Tilta firmware issue) The data stream out of the EXT port has a timing issue that Tilta are aware of and looking at correcting. The bug shows if you move more than one axis on the hand unit at a time, they will interrupt each other, then once you stop moving the axis, the motors will settle into position.
Nucleus-M II motor not passing data when used as wireless hub on FIZBUSTER. You can mount a Nucleus-M motor to the FIZBUSTER, make it motor 4 in the settings, then it becomes a wireless hub for your hand unit to connect to via Tilta 2.4ghz. Unfortunately this cool trick doesn't work for Nucleus M II motors currently, as Tilta arent passing data they receive wirelessly, out on the EXT ports.
Ronin 4D / Inspire 3
Added function to hand off only Focus and Iris to the DJI Hand unit, retaining Zoom on the Control Deck. Control Deck Menu : FIZ Control : FIZ / Zoom / Off
R/S Bug fixes for Control Deck, CANBUSTER and FIZBUSTER Known Bugs or limitations
DJI High-Bright monitor (DJI firmware issue) If you want to record proxies to the micro SD card, ensure you have General Setting : Recording Device set to TX+SD
Ronin 4D 8K Head (DJI Factory issue) The first time you connect a brand new X9-8K head to a Ronin 4D body, the tilt and roll will be swapped. To correct this factory bug, you must do a factory reset on the 4D. Unfortunately this means you will lose any lens mapping on that 4D body!
No touch focus with High-Bright monitor connect to Inspire 3 (DJI limitation) The work around: On pilot's RC Plus, set one of the custom buttons to 'Trigger Focus'. Then on Control Deck hit AF/MF to toggle to AF. Then the pilot can hit the custom button on their controller and trigger the AF point!
Ronin 2
Compatibility with Servo Link (Fusion Hub required)
R/S Bug fixes for Control Deck, CANBUSTER and FIZBUSTER
RS3 Pro / RS4 Pro
Compatibility with Servo Link (Fusion Hub required)
R/S Bug fixes for Control Deck, CANBUSTER and FIZBUSTER
MōVI Pro / MōVI XL / MōVI Carbon (Requires Fusion Hub!)
Compatibility with Servo Link (Fusion Hub required)
Added absolute based control for the gimbals, which means we then now do pan, tilt, roll and all axis recenter!
More consistent MōVI FIZ motor setting changes
R/S Bug fixes for Control Deck, CANBUSTER and FIZBUSTER
Last updated