Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Control Deck, as well as the other products in the Control Ecosystem are the result of a collaboration between Ignite Digi and our friend Tad Errey (Signal Audio), who is based in Melbourne, Australia. Tad is the programming wizard that enables seemingly disparate products like DJI Transmission and Tilta Nucleus, to all play nice together! 🔥
Welcome to the Control Deck Manual. This document is continuously updated as new functions, firmware and accompanying products are released. You can export this as a PDF via the â‹® in the top right. If possible, we recommend you reference the site though, as then it will never be out of date!
Cheese Block Mounted to the back of Control Deck, you will find the Cheese Block. Designed for solid mounting to light stand or other baby pin (5/8" / 16mm) and hex pin spigots.
If you're not running the Pro-Workflow monitor mount, then use the top ¼”-20” or ⅜"-16” threaded holes with Pin-Locks to mount a monitor arm. If not using a stand, you can mount an Arca Swiss or similar tripod plate to the ¼”-20” or ⅜"-16” threaded holes underneath. This may not work, depending on battery plate choice.
Pro-workflow Monitor Mount
Get to know Control Deck.
Large, custom machined, aluminium knob for precise focus operation with 325° of range.
Large rocker which can be assigned to either ZOOM or ROLL control.
A way to quickly control the Pan/Tilt/Roll speeds at a global level from 0-100%.
Allows operator control of the Iris or VND depending on setup.
Trigger Run/Stop of Inspire 3, Ronin 4D,
The red LED is visible with
For other overlays
The ultra-compact RovyVon Aurora A3 (Gen4) USB-C Flashlight features an aluminium case, impressive 5000K LED with 90+ CRI, max brightness of 650 lumens and four brightness settings - moonlight, low, medium, and high.
How to use the Aurora A3 Flashlight:
1) Lock: rapid click 5 times, the emitter blinks twice.
2) Unlock: rapid click 5 times when the light is locked, the emitter blinks 3 times.
3) Constant on: rapid double click to turn on from the memorised mode, then single click to cycle through moon-low-med-high; press the button for 0.5s to turn off.
***Memory is stored when the flashlight remains on for 3+ minutes.
4) Emergency mode: rapid triple click to turn on the strobe mode, then click to turn off.
The custom made 12-inch / 30cm USB-C Gooseneck keeps the flashlight battery charged and in a pinch could be used to charge a device like a Tentacle Sync or phone.
It plugs into the 30W USB-C Output at the left rear of the case. This deep recessed pocket supports the connector and prevents damage to the port.
Designed for solid mounting to light stand or other baby pin (5/8"/16mm) and hex pin spigots. If you're not running the Pro-Workflow monitor mount, then use the ¼”-20” or ⅜"-16” threaded holes with Pin-Locks to mount a monitor arm.
The 4-inch Tilting NATO Rail allows you to adjust for viewing comfort, and the two bolts attaching the High-Bright Monitor cage ensure no twist.
¼”-20” and ⅜"-16” threaded holes with Pin-Locks on the NATO rail allow you to use SmallHD or other 7" monitors with a Cine Lock or LNK quick releases, in use cases where the the 1st AC wants the DJI High-Bright or you prefer a SmallHD monitor.
The DJI High-Bright Remote Monitor requires the DJI Remote Monitor Expansion Plate (DC-IN / HDMI / SDI). This module is sold separately.
Adjust Pan speed from 0-100 and short press in for Pan axis recenter
Adjust Tilt speed from 0-100 and short press in for Tilt axis recenter. Long press in, when using Inspire 3, will activate 'Tilt to 90° down'.
Adjust roll trim on gimbal to allow for horizon drift. Approx. 3° each way of gimbal adjustment, with a detent in middle for 0°.
This switch turns on the Control Deck and passes power through to the DJI High-Bright Monitor and any accessories.
Short press for Roll axis recenter. Long press to invert tilt direction.
Twist can control either Zoom or the Roll axis. Change the function, or disable the axis in the Control Deck menu.
Premium APEM Joystick means greater accuracy and consistency. Square shape Limiter.
OLED display for showing menu, axis speeds and other functions.
Relevant to 4D and Inspire 3 only, you can place marks on the DJI High-Bright Monitor's Focus overlay. Short press to mark, long press to clear all marks. When using Fusion Hub, short press will crash zoom in for focus check. Short press again and it will quickly zoom back out to your previous focal length.
EXP is a shortcut to toggling on/off the exposure assistance of the DJI High-Bright Monitor You can choose in monitor's menu whether it toggles Zebra, Waveform or False Colour. PEAK is a shortcut to toggling on/off the focus peaking assistance of the DJI High-Bright Monitor You can adjust in monitor's menu the colour and intensity of the peaking.
Short press to toggle the lens between AF (autofocus) and MF (manual focus). Applicable only to Ronin 4D / Inspire 3 / R2 with LiDAR Hub / RS4 Pro with LiDAR Hub
Short press for all axis recenter. Long press to change gimbal modes.
Adjust the gimbal smoothness 0 - 30. This is how much ease in and out the gimbal does to your movements.
Adjust the deadband for the joystick for Pan, Tilt and Roll between 0 - 30. As well as deadband and gimbal smoothness, we offer the operator a choice of joystick expo curves.
Linear — 1:1 input to output, if using this mode you will ride the master rate for more finesse of tilt/pan speed on the go.
Square — provides finer control of lower speed moves, while still being able to run a reasonably high pan/tilt speed.
Cubic — suitable for when you want to run really high speed on tilt/pan, but still have fine control for slow movement.
Long press to enable/disable shake mode. Adjust the scale between 0-30 using the knob. In menu you can enable or disable individual axis. Smoothness setting affects the shake function as well.
A carbon plate protects the USB-C port and button from dust and moisture. Only for Firmware Updates!
Pan
âś“
âś“
Tilt
âś“
âś“
Roll
âś“
âś“
Pan, Tilt, Roll speed
âś“
âś“
Master Rate
âś“
âś“
Roll Trim
âś“
âś“
Tilt to 90° down
X
âś“
Shake
âś“
âś“
Run/Stop
âś“ with indicator LED
âś“ with indicator LED
Recenter
Pan, Tilt, Roll, All
Pan, Tilt, Roll, All
Joystick Deadband
âś“
âś“
Smoothness
âś“
âś“
Gimbal mode
X
âś“ Follow and Dual Op via High-Bright Monitor
Focus
âś“
âś“
Iris
âś“
âś“
Zoom
âś“
N/A
Focus Range
âś“ Full / Half / Third
âś“ Full / Half / Third
Iris Range
âś“ Full / Half
âś“ Full / Half
Compatible with DJI 3ch Hand Unit or Focus Pro Hand Unit
âś“ via Control Link OR second DJI High-Bright and Remote Monitor Holder
âś“ via Control Link
ISO
âś“ via High-Bright Monitor
âś“ via High-Bright Monitor
WB
âś“ via High-Bright Monitor
âś“ via High-Bright Monitor
FPS
âś“ via High-Bright Monitor
âś“ via High-Bright Monitor
Shutter
âś“ via High-Bright Monitor
âś“ via High-Bright Monitor
ND
âś“ via High-Bright Monitor
N/A
EXP / PEAK
âś“
âś“
AF / MF toggle
âś“
âś“
Focus Marks
âś“
âś“
Mirror mode
âś“
N/A
This function chart covers: MoVI Pro/XL, Ronin 2, RS3 Pro/RS4 Pro, BaseCam Electronics when utilising the Fusion Hub and DJI Transmission TX with Nucleus-M, M II or Nano II motors
Pan
âś“
âś“
âś“
âś“
âś“
âś“
Tilt
âś“
âś“
âś“
âś“
âś“
âś“
Roll
âś“
âś“
âś“
âś“
âś“
âś“
Pan, Tilt, Roll speed
âś“
âś“
âś“
âś“
âś“
âś“
Master Rate
âś“
âś“
âś“
âś“
âś“
âś“
Roll Trim
âś“
âś“
âś“
âś“
âś“
âś“
Shake
âś“
âś“
âś“
âś“
âś“
âś“
Recenter
Pan, Tilt, Roll, All
Pan, Tilt, Roll, All
Pan, Tilt, Roll, All
Pan, Tilt, Roll, All
X
Tilt, Roll, 'Return to Horizon' (Tilt/Roll)
Joystick Deadband
âś“
âś“
âś“
âś“
âś“
âś“
Smoothness
âś“
âś“
âś“
âś“
âś“
âś“
Gimbal mode
âś“ Majestics, Dual, Kill
âś“ via User Profiles 1-5
âś“ PTF, Custom
X
X
âś“ Control (User 1), Kill Motors (User 2)
Focus
âś“
âś“
âś“
âś“
âś“
âś“
Iris
âś“
âś“
âś“
âś“
âś“
âś“
Zoom
âś“
âś“
âś“
âś“
âś“
âś“
FIZ Speed / Torque / Direction
âś“
âś“
âś“
âś“
âś“
Crash Zoom
âś“
âś“
âś“
âś“
âś“
Zoom Scaling / PTR Ratio
âś“
âś“
âś“
âś“
âś“
Focus Curve
âś“
âś“
âś“
âś“
âś“
âś“
EXP / PEAK
âś“
âś“
âś“
âś“
âś“
âś“
Compatible with FIZBUSTER - FIZ Hand off to Nucleus hand unit
âś“
âś“
âś“
âś“
âś“
âś“
Compatible with SERVO LINK
âś“
âś“
âś“
âś“
âś“
âś“
This function chart covers: Ronin 2, RS3 Pro/RS4 Pro when using DJI RS LiDAR Hub or DJI Focus Pro LiDAR Hub with DJI Transmission TX, with Focus Pro or RS motors
Pan
âś“
âś“
Tilt
âś“
âś“
Roll
âś“
âś“
Pan, Tilt, Roll speed
âś“
âś“
Master Rate
âś“
âś“
Roll Trim
âś“
âś“
Shake
âś“
âś“
Recenter
Pan, Tilt, Roll, All
Pan, Tilt, Roll, All
Joystick Deadband
âś“
âś“
Smoothness
âś“
âś“
Gimbal mode
âś“ via User Profiles 1-5
âś“ PTF, Custom
Focus (*1 motor only!)
âś“*
âś“*
Iris
X
X
Zoom
âś“*
âś“*
EXP / PEAK
âś“
âś“
AF / MF toggle
âś“
âś“
Control Deck FAQ
In FCC mode, the High-Bright should have more range than the RC Plus, with higher gain in it's TX for control, plus the ability to separate the antennas and get them above head height. In CE/SRRC/MIC mode, they both have the same limits. In reality, we have found that the Inspire 3 throttles the transmission data rate to both RC Plus and High-bright simultaneously to keep connection. So you should have connection on both until you don't have any connection at all. Transmission info from DJI: RC Plus 2.4 GHz: <26 dBm (FCC), <20 dBm (CE/SRRC/MIC) 5.1 GHz (FPV camera video feed): <26 dBm (FCC), <23 dBm (CE/SRRC/MIC) 5.8 GHz: <26 dBm (FCC/SRRC), <14 dBm (CE)
High-Bright 2.4 GHz: <33 dBm (FCC), <20 dBm (CE/SRRC/MIC) 5.8 GHz: <33 dBm (FCC), <14 dBm (CE), <23 dBm (SRRC)
Underneath the Control Deck, showing battery plate (V-Mount, Gold Mount, TB50, TB51), rubber feet and serial number plate. The battery plates use a 3-pin Molex connector, making them user swappable.
6-PIN LEMO DC IN - 11-17V input for external powering of Control Deck and it's accessory ports. Wiring is the same as DJI Transmission and RED DSMC1/2/3 cameras, so if you have any D-tap or 4-pin XLR cables to those cameras, you can use on this port. It's also where the 90W AC Adapter plugs in!
USB-C 30W output This port is recessed to support the USB-C Gooseneck Flashlight, but it also is great for charging iPhones, iPads or even the pilot's RC Plus! Not every USB-C cable will fit into the recessed hole. DJI, Apple and other thin cables will work nicely.
6-PIN LEMO TRANSMISSION - 11-17V and CANBUS out for external powering and control data to the DJI High-Bright. Wiring is the same as DJI Transmission, so any male to female 6-pin 1B Lemo cable, made for DJI Transmission or Control Deck, will work.
7-PIN LEMO TILTA - 11-17V out and data for FIZBUSTER functionality. Only on Control Deck's with serial number #0100 and above have this. Plug in Tilta Nucleus-M I or II hand unit to Control Deck, allowing you to hand off FIZ to 1st AC. Alternatively, mount a Nucleus-M I (II motors don't work yet, Tilta have to do a firmware update) and use that as a wireless hub to connect hand unit via Tilta's 2.4ghz link. This port will output 11-17V to power the Nucleus-M Hand Unit, plus data connection between them.
2-PIN LEMO POWER - 11-17V out for powering accessories such as SmallHD monitor, where you may have given the 1st AC the DJI monitor for focus overlays. Rated up to 5 amp draw. Control Deck's with serial number #0100 and above you will have one 2-pin port. Control Deck's with serial number #0001 - #0099, you will have two 2-pin ports.
USB-C for computer connection - Data only, no power out This port connects to your computer, allowing firmware updates or to be used as a controller for applications like Cam Op Simulator. The small button above is to put the Controller into firmware flashing mode.
This is in order as you will see it on the Control Deck when connected to a Ronin 4D or Inspire 3
Control Deck remembers it's previous settings when power cycling, or you reconnect to a device type. Example: Going between 4D and Ronin 2, any 4D specific settings will be remembered for when you connect back to it.
Exit Menu
-
You can quickly exit the menu at anytime, by holding MENU/SETUP button (second from right)
Joystick Expo
L / 2 / 3
Joystick Fn
Twist: On/Off Button: On/Off
Enable or Disable the Twist Axis or Button on the Joystick. Twist setting ON is not overridden by Roll Speed OFF
PTR Direction
Axis: P/T/R Invert: Off/On
Toggle the control direction for Pan, Tilt and Roll axis. Shortcut for toggling Tilt Axis direction is still long hold on Joystick Button (in most modes), unless button is turned off in Joystick Fn (above)
Roll Speed
Off / L / M / H
Off : Disable roll input on Joystick or Rocker. Roll Trim will ALWAYS remain available! L: Low M: Medium H: High
Zoom/Roll Swap
Normal / Swapped
Normal is Zoom on Rocker, Roll on Twist. Swapped is Roll on Rocker, Zoom on Twist
FIZ Control
FIZ / Zoom / Off
FIZ: Control on Control Deck Zoom: Control only zoom (4D), use DJI hand unit for Focus and Iris Off: Hand off all FIZ control to DJI hand unit
Focus Knob Cal.
Calibrate
This calibrates the focus knob on the Control Deck, not the FIZ motors! Turn the Focus Knob to each end gently until it says Complete. You may find it says Complete after just a partial movement, this is because it's tracking the endpoints in the background even when you're not in the menu. It will only calibrate for the full range of the knob.
Focus Range
Full / Half / Third
Full: maps the full lens focus range to the full range of the focus knob. Half: maps the far half of the lens focus range to the full range of the focus knob. Third: maps the far third of the lens focus range to the full range of the focus knob. Super useful for Inspire 3 focus
Iris Range
Full / Half
Full: maps the full lens iris range to the full range of the iris knob. Half: maps the open half of the lens iris range to the full range of the iris knob. Eg: F4 - F10 on Sony 16-35mm PZ f4
Shake Mode
1 / 2 / 3
Change the shake algorithm
Shake On Move
On / Off
On: Shake will continue on all axes, regardless of joystick input. Off: Shake will only be on axis that are not getting input from joystick, once input from joystick stops that axis will ease into shake again.
Shake Axis
Axis: P / T / R Shake: On / Off
Enable or disable shake on each axis: Pan / Tilt / Roll
FIZ Axis Inverts
Invert Zoom Stick On/Off Invert Focus Knob On/Off Invert Iris Slider On/Off
On HBM, go to ... in bottom left then General Settings -> Three-Channel Follow Focus Settings. This allows you to change the direction focus, iris and zoom move relative to the Control Deck's inputs.
EXP Button
Waveform False Color Zebra Stripes
On HBM, go to ... in bottom left then General Settings -> Custom Hand Grips. This allows you to change the exposure tool that shows up on screen when you press EXP on Control Deck.
Unit
Imperial / Metric
On HBM, go to ... in bottom left then General Settings -> Unit Choose Metric or Freedom Units for your lens overlays on screen.
This is in order as you will see it on the Control Deck when connected to a Ronin 2 / RS4 Pro
Control Deck remembers it's previous settings when power cycling, or you reconnect to a device type. Example: Going between 4D and Ronin 2, any 4D specific settings will be remembered for when you connect back to it.
Exit Menu
-
You can quickly exit the menu at anytime, by holding MENU/SETUP button (second from right)
Joystick Expo
L / 2 / 3
Joystick Fn
Twist: On/Off Button: On/Off
Enable or Disable the Twist Axis or Button on the Joystick. Twist setting ON is not overridden by Roll Speed OFF
PTR Direction
Axis: P/T/R Invert: Off/On
Toggle the control direction for Pan, Tilt and Roll axis. Shortcut for toggling Tilt Axis direction is still long hold on Joystick Button (in most modes), unless button is turned off in Joystick Fn (above)
Roll Speed
Off / L / M / H
Off : Disable roll input on Joystick or Rocker. Roll Trim will ALWAYS remain available! L: Low M: Medium H: High
Zoom/Roll Swap
Normal / Swapped
Normal is Zoom on Rocker, Roll on Twist. Swapped is Roll on Rocker, Zoom on Twist
FIZ Control *this setting will disappear when Fusion Hub setting is On.
FIZ / Zoom / Off
FIZ: Control 1 x DJI RS or Focus Pro Motor that's on RS4 Pro, or on LiDAR Hub. Zoom: Not applicable to this use case Off: No FIZ motor control
Focus Knob Cal.
Calibrate
This calibrates the focus knob on the Control Deck, not the FIZ motors! Turn the Focus Knob to each end gently until it says Complete. You may find it says Complete after just a partial movement, this is because it's tracking the endpoints in the background even when you're not in the menu. It will only calibrate for the full range of the knob.
Shake Mode
1 / 2 / 3
Change the shake algorithm
Shake On Move
On / Off
On: Shake will continue on all axes, regardless of joystick input. Off: Shake will only be on axis that are not getting input from joystick, once input from joystick stops that axis will ease into shake again.
Shake Axis
Axis: P / T / R Shake: On / Off
Enable or disable shake on each axis: Pan / Tilt / Roll
RS Motor *this setting will disappear when Fusion Hub setting is On.
Knob / Rocker
Knob: Control the RS/Focus Pro motor via the focus knob on Control Deck. Rocker: Control the RS/Focus Pro motor via the rocker on Control Deck.
R2 User Profile
1 / 2 / 3 / 4 / 5
When using RS4 Pro: 1: PTF 2: FPV / 3D Roll 360 / Custom We recommend setting to Custom and then turning off each axis follow via the pencil symbol top right of the gimbal screen. 3/4/5: N/A When using Ronin 2: 1: User Profile 1 2: User Profile 2 3: User Profile 3 4: User Profile 4 5: User Profile 5 A long press of MODE button on Control Deck will cycle between User 1 and 2 on RS4 Pro and Ronin 2
Fusion Hub
Off / On
Off: If no Fusion Hub is in line, ensure you have this setting to Off. If you have it set to On but have no Fusion Hub in line, you will get erratic gimbal movements. On: For use when you have Fusion Hub on the DJI TX. See below for the new menu items that appear when this setting is On.
Focus Curve
25% / 50% / 75%
Gives you the ability to offset the focus mapping for more precision at one end of the lens' focus range.
Similar to Near/Far setting on your Canon/Fujinon focus demand.
Works with Nucleus-M, M2, Nano II, MĹŤVI motors and Servo lenses.
Fusion Focus
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the focus knob
Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Iris
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the iris knob
Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom A
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the zoom rocker *not applicable when using Servo lens Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom B
Speed : L / M / H Damping : L / M / H
Speed L / M / H: Set the maximum speed of the zoom. Damping L / M / H: Set the amount of damping, to help ease in and out of zooms
MĹŤVI Motor Type
0 - 7 (in 1 step increments)
This setting is not applicable for Ronin 2 / RS4 Pro use case
Iris Control
Iris / ND
Change the mapping of iris knob between iris and VND when using Tilta Nucleus M, M2 or Nano II motors. Iris (motor 2) VND (motor 4)
FIZ Handoff
FIZ / FI / F / I
Use this setting to hand off FIZ axis to the Tilta Hand Unit connected to FIZBUSTER (standalone or rear port of Control Deck) FIZ: Focus, Iris and Zoom FI: Focus and Iris (Control Deck still has Zoom) F: Focus (Control Deck still has Iris and Zoom) I: Iris (Control Deck still has Focus and Zoom)
Servo Link
FIZ / FZ
Only applicable when using Servo Link Allows you to control iris on Servo lenses, or to relinquish iris control to the camera, for auto iris or CCU control. FIZ: You will have Focus, Iris and Zoom on Control Deck FZ: You will have Focus and Zoom on Control Deck
PTR/Zoom Ratio
1:1 - 1:25 (in 1 step increments)
Also known as Zoom scaling, it allows you to set a ratio of how much the pan/tilt/roll axis speeds will lower relative to the zoom position of the lens. Example: Canon 17-120mm, try 7:1 setting. As you zoom in, Control Deck will adjust the axis speeds for a consistent feel and look.
FIZ Calibrate
Calibrate
Remotely trigger calibrate on Nucleus-M, M2, Nano II or MĹŤVI FIZ motors. If the motors have recently completed a calibration, then this may not work. Not applicable when using Servo Link
This is in order as you will see it on the Control Deck when connected to a MĹŤVI Pro / XL
Control Deck remembers it's previous settings when power cycling, or you reconnect to a device type. Example: Going between 4D and Ronin 2, any 4D specific settings will be remembered for when you connect back to it.
Exit Menu
-
You can quickly exit the menu at anytime, by holding MENU/SETUP button (second from right)
Joystick Expo
L / 2 / 3
Joystick Fn
Twist: On/Off Button: On/Off
Enable or Disable the Twist Axis or Button on the Joystick. Twist setting ON is not overridden by Roll Speed OFF
PTR Direction
Axis: P/T/R Invert: Off/On
Toggle the control direction for Pan, Tilt and Roll axis. Shortcut for toggling Tilt Axis direction is still long hold on Joystick Button (in most modes), unless button is turned off in Joystick Fn (above)
Roll Speed
Off / L / M / H
Off : Disable roll input on Joystick or Rocker. Roll Trim will ALWAYS remain available! L: Low M: Medium H: High
Zoom/Roll Swap
Normal / Swapped
Normal is Zoom on Rocker, Roll on Twist. Swapped is Roll on Rocker, Zoom on Twist
Focus Knob Cal.
Calibrate
This calibrates the focus knob on the Control Deck, not the FIZ motors! Turn the Focus Knob to each end gently until it says Complete. You may find it says Complete after just a partial movement, this is because it's tracking the endpoints in the background even when you're not in the menu. It will only calibrate for the full range of the knob.
Shake Mode
1 / 2 / 3
Change the shake algorithm
Shake On Move
On / Off
On: Shake will continue on all axes, regardless of joystick input. Off: Shake will only be on axis that are not getting input from joystick, once input from joystick stops that axis will ease into shake again.
Shake Axis
Axis: P / T / R Shake: On / Off
Enable or disable shake on each axis: Pan / Tilt / Roll
R2 User Profile
1 / 2 / 3 / 4 / 5
1: Dual Op 2: Majestic Pan + Roll (Remote Tilt) 3: Kill motors 4: Majestic Roll (Pan + Tilt remote) 5: Majestic Pan + Tilt + Roll (no remote) A long press of MODE button on Control Deck will cycle between Dual Op and Majestic Pan + Roll (Remote Tilt) Modes on MĹŤVI Pro / XL A long press of CLEAR MARK button on Control Deck will cycle between Kill gimbal motors and Dual Op Modes on MĹŤVI Pro / XL
Fusion Hub
Off / On
Off: If no Fusion Hub is in line, ensure you have this setting to off. If you have it set to On but have no Fusion Hub in line, you will get erratic gimbal movements. On: For use when you have Fusion Hub on the DJI TX. See below for the new menu items that appear when this setting is On.
Focus Curve
25% / 50% / 75%
Gives you the ability to offset the focus mapping for more precision at one end of the lens' focus range.
Similar to Near/Far setting on your Canon/Fujinon focus demand.
Works with Nucleus-M, M2, Nano II, MĹŤVI motors and Servo lenses.
Fusion Focus
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the focus knob
Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Iris
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the iris knob
Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom A
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the zoom rocker *not applicable when using Servo lens Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom B
Speed : L / M / H Damping : L / M / H
Speed L / M / H: Set the maximum speed of the zoom. Damping L / M / H: Set the amount of damping, to help ease in and out of zooms
MĹŤVI Motor Type
0 - 7 (in 1 step increments)
Allows you to change the motor type setting on MĹŤVI Pro/XL to match the motors you are using.
0: Redrock Torque/SLS motor 1: Heden M26 2: Heden M21 3: Hocus Axis1 4: Hocus Reflex 5: Chrosziel100 6: Custom1 7: Custom2
Iris Control
Iris / ND
Change the mapping of iris knob between iris and VND when using Tilta Nucleus M, M2 or Nano II motors. Iris (motor 2) ND (motor 4)
FIZ Handoff
FIZ / FI / F / I
Use this setting to hand off FIZ axis to the Tilta Hand Unit connected to FIZBUSTER (standalone or rear port of Control Deck) FIZ: Focus, Iris and Zoom FI: Focus and Iris (Control Deck still has Zoom) F: Focus (Control Deck still has Iris and Zoom) I: Iris (Control Deck still has Focus and Zoom)
Servo Link
FIZ / FZ
Allows you to control iris on Servo lenses, or to relinquish iris control to the camera, for auto iris or CCU control. FIZ: You will have Focus, Iris and Zoom on Control Deck FZ: You will have Focus and Zoom on Control Deck
PTR/Zoom Ratio
1:1 - 1:25 (in 1 step increments)
Also known as Zoom scaling, it allows you to set a ratio of how much the pan/tilt/roll axis speeds will lower relative to the zoom position of the lens. Example: Canon 17-120mm, try 7:1 setting. As you zoom in, Control Deck will adjust the axis speeds for a consistent feel and look.
FIZ Calibrate
Calibrate
Remotely trigger calibrate on Nucleus-M, M2, Nano II or MĹŤVI FIZ motors. If the motors have recently completed a calibration, then this may not work.
This is in order as you will see it on the Control Deck when connected to a TORQ Head, Titan LT
Control Deck remembers it's previous settings when power cycling, or you reconnect to a device type. Example: Going between 4D and Ronin 2, any 4D specific settings will be remembered for when you connect back to it.
Exit Menu
-
You can quickly exit the menu at anytime, by holding MENU/SETUP button (second from right)
Joystick Expo
L / 2 / 3
Joystick Fn
Twist: On/Off Button: On/Off
Enable or Disable the Twist Axis or Button on the Joystick. Twist setting ON is not overridden by Roll Speed OFF
PTR Direction
Axis: P/T/R Invert: Off/On
Toggle the control direction for Pan, Tilt and Roll axis. Shortcut for toggling Tilt Axis direction is still long hold on Joystick Button (in most modes), unless button is turned off in Joystick Fn (above)
Roll Speed
Off / L / M / H
Off : Disable roll input on Joystick or Rocker. Roll Trim will ALWAYS remain available! L: Low M: Medium H: High
Zoom/Roll Swap
Normal / Swapped
Normal is Zoom on Rocker, Roll on Twist. Swapped is Roll on Rocker, Zoom on Twist
Focus Knob Cal.
Calibrate
This calibrates the focus knob on the Control Deck, not the FIZ motors! Turn the Focus Knob to each end gently until it says Complete. You may find it says Complete after just a partial movement, this is because it's tracking the endpoints in the background even when you're not in the menu. It will only calibrate for the full range of the knob.
Shake Mode
1 / 2 / 3
Change the shake algorithm
Shake On Move
On / Off
On: Shake will continue on all axes, regardless of joystick input. Off: Shake will only be on axis that are not getting input from joystick, once input from joystick stops that axis will ease into shake again.
Shake Axis
Axis: P / T / R Shake: On / Off
Enable or disable shake on each axis: Pan / Tilt / Roll
R2 User Profile
1 / 2 / 3 / 4 / 5
1: Dual Op 2: Majestic Pan + Roll (Remote Tilt) 3: Kill motors 4: Majestic Roll (Pan + Tilt remote) 5: Majestic Pan + Tilt + Roll (no remote) A long press of MODE button on Control Deck will cycle between Dual Op and Majestic Pan + Roll (Remote Tilt) Modes on MĹŤVI Pro / XL A long press of CLEAR MARK button on Control Deck will cycle between Kill gimbal motors and Dual Op Modes on MĹŤVI Pro / XL
Fusion Hub
Off / On
Off: If no Fusion Hub is in line, ensure you have this setting to off. If you have it set to On but have no Fusion Hub in line, you will get erratic gimbal movements. On: For use when you have Fusion Hub on the DJI TX. See below for the new menu items that appear when this setting is On.
Focus Curve
25% / 50% / 75%
Gives you the ability to offset the focus mapping for more precision at one end of the lens' focus range.
Similar to Near/Far setting on your Canon/Fujinon focus demand.
Works with Nucleus-M, M2, Nano II, MĹŤVI motors and Servo lenses.
Fusion Focus
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the focus knob
Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Iris
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the iris knob
Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom A
Dir. : CW / CCW Torque : L / M / H
Dir.
CW / CWW: Change the direction of the motor relative to the zoom rocker *not applicable when using Servo lens Torque L / M / H: Set the motor torque for the Focus motor. *not applicable when using Servo lens
Fusion Zoom B
Speed : L / M / H Damping : L / M / H
Speed L / M / H: Set the maximum speed of the zoom. Damping L / M / H: Set the amount of damping, to help ease in and out of zooms
MĹŤVI Motor Type
0 - 7 (in 1 step increments)
Allows you to change the motor type setting on MĹŤVI Pro/XL to match the motors you are using.
0: Redrock Torque/SLS motor 1: Heden M26 2: Heden M21 3: Hocus Axis1 4: Hocus Reflex 5: Chrosziel100 6: Custom1 7: Custom2
Iris Control
Iris / ND
Change the mapping of iris knob between iris and VND when using Tilta Nucleus M, M2 or Nano II motors. Iris (motor 2) ND (motor 4)
FIZ Handoff
FIZ / FI / F / I
Use this setting to hand off FIZ axis to the Tilta Hand Unit connected to FIZBUSTER (standalone or rear port of Control Deck) FIZ: Focus, Iris and Zoom FI: Focus and Iris (Control Deck still has Zoom) F: Focus (Control Deck still has Iris and Zoom) I: Iris (Control Deck still has Focus and Zoom)
Servo Link
FIZ / FZ
Allows you to control iris on Servo lenses, or to relinquish iris control to the camera, for auto iris or CCU control. FIZ: You will have Focus, Iris and Zoom on Control Deck FZ: You will have Focus and Zoom on Control Deck
PTR/Zoom Ratio
1:1 - 1:25 (in 1 step increments)
Also known as Zoom scaling, it allows you to set a ratio of how much the pan/tilt/roll axis speeds will lower relative to the zoom position of the lens. Example: Canon 17-120mm, try 7:1 setting. As you zoom in, Control Deck will adjust the axis speeds for a consistent feel and look.
FIZ Calibrate
Calibrate
Remotely trigger calibrate on Nucleus-M, M2, Nano II or MĹŤVI FIZ motors. If the motors have recently completed a calibration, then this may not work.
Required: 6-pin male to 6-pin Female 1B Lemo cable from DJI or Ignite Digi. Power and data. DJI High-Bright combo includes 1 x straight male to straight female cable which can be used. We sell a 10" cable straight to right angle (IG.100391, pictured below) which works really nicely for TX mounted to R2 Accessory mounts.
Use IG.100539 cable to run from Ronin 2 Power Hub to the 7-pin 0B Lemo port on the side of the Focus Pro LiDAR Hub. This passes 14.4V power from the Ronin 2 to the LiDAR Hub/Transmission and control data back to the Ronin 2.
Use IG.100474 cable to run from Ronin 2 Power Hub to the USB-C port on the side of the RS LiDAR Hub. This passes control data from LiDAR Hub/Transmission to the Ronin 2. To power, plug the D-tap of the LiDAR Hub into the R2->D-tap splitter that DJI include with the Ronin 2.
